Catalyst palladium

New downstream synthetic route of 52522-40-4

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,Tris(dibenzylideneacetone)dipalladium-chloroform,52522-40-4,its application will become more common.

A common heterocyclic compound, 52522-40-4,Tris(dibenzylideneacetone)dipalladium-chloroform, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 52522-40-4

General procedure: To 64.3 mg (0.278 mmol) of TTbQ-Me dissolved in anhydrous acetone (20 ml) in a two necked flask, 30 mg (0.278 mmol) of p-benzoquinone and 120 mg (0.116 mmol) of Pd2DBA3CHCl3 were added in sequence under inert atmosphere (Ar). The resulting mixture was stirred in the dark for 30 min, filtered on a celite filter and evaporated under vacuum to a small volume. Addition of Et2O induces the precipitation of the complex which was filtered off and dried in a desiccator for 5 h. 82.2 mg of the title compound as a red solid were obtained (yield 80percent).

Reference£º
Article; Canovese, Luciano; Visentin, Fabiano; Santo, Claudio; Bertolasi, Valerio; Journal of Organometallic Chemistry; vol. 749; (2014); p. 379 – 386;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

The origin of a common compound about 887919-35-9

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,887919-35-9,Bis(di-tert-butyl(4-dimethylaminophenyl)phosphine)dichloropalladium(II),its application will become more common.

A common heterocyclic compound, 887919-35-9,Bis(di-tert-butyl(4-dimethylaminophenyl)phosphine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 887919-35-9

Step 3-4, Preparation of tert-butyl (3R)-4-[4-(2-ethoxypyridin-3-yl)-3-fluoro-2-(methoxycarbonyl)phenyl]-3-ethylpiperazine-1-carboxylate To a mixture of tert-butyl (3R)-4-[4-bromo-3-fluoro-2-(methoxycarbonyl)phenyl]-3-ethylpiperazine-1-carboxylate (267 mg, 0.600 mmol), (2-ethoxypyridin-3-yl)boronic acid (150 mg, 0.900 mmol), Pd[t-Bu2P(4-NMe2C6H4)]2Cl2) (42.5 mg, 0.0600 mmol), and K2CO3 (249 mg, 1.80 mmol) in a sealed tube was added dioxane (4 mL) and H2O (0.4 mL). The resulting solution was degassed with N2 (g) for 10 min, sealed, and stirred at 100 C. for 30 min. The reaction was treated with additional (2-ethoxypyridin-3-yl)boronic acid (37.8 mg, 0.226 mmol), Pd[t-Bu2P(4-NMe2C6H4)]2Cl2) (13.4 mg, 0.0189 mmol), and K2CO3 (78.3 mg, 0.567 mmol) and stirred at 100 C. for additional 30 min. The mixture was concentrated and purified by C18 reversed phase column chromatography to give the title compound (255 mg, 87% yield) as a brown gum. LCMS (M+H)+: 488.4.

Reference£º
Patent; Crinetics Pharmaceuticals, Inc.; HAN, Sangdon; ZHU, Yunfei; KIM, Sun Hee; ZHAO, Jian; WANG, Shimiao; (146 pag.)US2019/367481; (2019); A1;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

A new synthetic route of 52522-40-4

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,52522-40-4,Tris(dibenzylideneacetone)dipalladium-chloroform,its application will become more common.

A new synthetic route of (2,2¡ä-Bipyridine)dichloropalladium(II)

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),its application will become more common.

A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14871-92-2

General procedure: Solid [Pd(L)Cl2] (L = bpy, phen) (0.2 mmol) was added to methanolic solution H2mesc (0.039 g, 0.2 mmol) containing KOH (0.0224 g, 0.4 mmol;; 15 mL). The mixture was stirred for 24 h. The yellow precipitate was filtered off, washed with methanol and air-dried. For [Pd(bpy)(mesc)]: Anal. Calc. For C20H15N2O4.5Pd: C, 52.0; H, 3.3; N, 6.1; Pd, 23.1%, Found: C, 52.1, H, 3.2; N, 6.0; Pd, 23.0%. Conductivity data (10-3 M in DMSO): LambdaM = 2.0 Ohm-1 cm2 mol-1. IR (cm-1); nu(C=O) 1664; nu(C-C) 1486; nu(C-O) 1254; nu(Pd-O) 521; nu(Pd-N) 427. 1H NMR (d6-DMSO/TMS, ppm), delta: CH3, 3.36; H(3), 6.66; H(8), 5.90; H(5), 6.50. ESI-MS: m/z: 905 (Calcd 904.8) [Pd(bpy)(mesc)]2+, 453 (Calcd 452.4) [Pd(bpy)(mesc)]+.

Reference£º
Article; Butler, Ian S.; Gilson, Denis F.R.; Jean-Claude, Bertrand J.; Mostafa, Sahar I.; Inorganica Chimica Acta; vol. 423; PB; (2014); p. 132 – 143;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some scientific research about (2,2¡ä-Bipyridine)dichloropalladium(II)

14871-92-2 A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

Solid [Pd(bpy)Cl2] (0.166 g, 0.5 mmol) was added to dl-H2pa (0.064 g, 0.5 mmol) in ethanol (8 mL) containing triethyl amine (0.05 g, 0.5 mmol). The mixture was stirred for 72 h. The yellow-beige precipitate was filtered off, washed with ethanol and air-dried. Yield: 45%. Anal. Calcd. for C16ClH22N3O4Pd: C, 41.6; H, 4.8; N, 9.1; Cl, 7.7; Pd, 23.0%, Found: C, 41.5; H, 4.4; N, 9.0; Cl, 7.6; Pd, 23.1%. Conductivity data (10-3 M in DMF):LambdaM = 97.0 ohm-1. IR (cm-1): nu(NH) 3106; nuas(COO-) 1659; nus(COO-) 1411; nu(Pd-O) 521; nu(Pd-N) 471 cm-1. Raman: nuas(COO-) 1598; nus(COO-) 1402; delta(NH) 1560; nu(Pd-O) 529; nu(Pd-N) 450 cm-1; 1H NMR (d6-DMSO/TMS, ppm), 3.73 (d, H, Halpha); 2.50 (m, 2H, Hbeta); 2.07 (m, 2H, Hgamma); 1.30 (m, 2H, Hdelta); 3.45, 3.10 (m, 2H, Hepsilon); 13.19 (s, H, NH), ESI-MS: m/z, 816.7 {Pd(Hpa)(bpy)]2Cl}+, 780.7 {[Pd(bpy)(Hpa)]2}+, 390.0 [Pd(bpy)(Hpa)]+, 263.0 [Pd(bpy)]+., 14871-92-2

Reference£º
Article; Alie El-Deen, Afaf A.; El-Askalany, Abd El-Monem E.; Halaoui, Ruba; Jean-Claude, Bertrand J.; Butler, Ian S.; Mostafa, Sahar I.; Journal of Molecular Structure; vol. 1036; (2013); p. 161 – 167;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some scientific research about Tris(dibenzylideneacetone)dipalladium-chloroform

52522-40-4 A common heterocyclic compound, 52522-40-4,Tris(dibenzylideneacetone)dipalladium-chloroform, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

52522-40-4, Under inert gas protection,Tri-tert-butylphosphonium tetrafluoroborate (9.3 g, 0.032 mil,4Eq), tris (dibenzylideneacetone) dipalladium () chloroform adduct (8. 3g, 008 mol, leq) and 200 mlDimethyl sulfoxide was added to the reaction flask,And then slowly dropping to them1M sodium methoxide solution in methanol(32L, 0.032, 0e, 4eq),50 ¡ã C for 15 h.Gloves bag filter,The filter cake was washed with dimethyl sulfoxideThe The filter cake was dried in n-hexane.filter,The filtrate was concentrated and crystallized.filter,The filter cake was washed with a small amount of n-hexane and the filter cake was washed with a small amount of n-hexane and dried to give 3. 27 g of a white solid powder in 80percent yield, elemental analysis: C, 56.17;H, 10. 50; P, 12. 07; Pd, 21.26

Reference£º
Patent; Hebei bailingwei super fine material Co. Ltd.; Wang, Zhen; Liu, YunSheng; Deng, XongFei; (5 pag.)CN105273009; (2016); A;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

The origin of a common compound about 14871-92-2

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material., 14871-92-2

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some scientific research about Bis(tri-tert-butylphosphine)palladium

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,Bis(tri-tert-butylphosphine)palladium,53199-31-8,its application will become more common.

53199-31-8 A common heterocyclic compound, 53199-31-8,Bis(tri-tert-butylphosphine)palladium, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

B. Synthesis of 3-(1-pyrrolidinyl)phenol 7g (30 mmol) of 1-Bromo-3-methoxymethoxy-benzene from step A and 2,5 g (35 mmol) of pyrrolidine were dissolved under argon in 60 mL of toluene. Then, 0.15 g (0.3 mmol) of bis(tri-t-butylphosphine)palladium(0), 2,5g KOH und 0,6g (0,15 mmol) cetyltrimethylammoniumbromid were added, and the reaction mixture was heated at 80 C. At the end of the reaction, the reaction mixture was poured into 200 mL of ethyl acetate, and the organic phase was extracted with 1 N sodium hydroxide solution and then dried with magnesium sulfate. The solvent was distilled off in a rotary evaporator, and the residue was purified on silica gel using heptane/ethyl acetate (8/0,8). The product thus obtained was dissolved in 15 mL of ethanol and mixed with 10 mL of a 2.9 molar solution of ethanolic hydrochloric acid.

Reference£º
Patent; Wella Aktiengesellschaft; EP1752192; (2007); A1;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some scientific research about Tris(dibenzylideneacetone)dipalladium-chloroform

0.1624 g (0.4076 mmol) of 1,2-bis(diphenylphosphine)ethane, 0.1671 g (1.159 mmol) of dmfu and 0.2002 g (0.1934 mmol) of [Pd2(DBA)3*CHCl3] were dissolved under inert atmosphere (Ar) in 30 ml of anhydrous acetone and vigorously stirred for 60 min. Owing to the progressive dissolution of [Pd2(DBA)3*CHCl3], the violet color of the mixture gradually disappeared and the concomitant precipitation of the scarcely soluble pale yellow complex 1j was observed. The solution was dried under vacuum, the residue dissolved in CH2Cl2, treated with activated charcoal and filtered on a celite filter. The clear pale yellow solution was concentrated under vacuum and the title complex precipitated by slow addition of diethylether. Complex 1j was filtered off on a gooch, washed with diethylether and dried under vacuum. 0.2027 g (yield 81percent) of the title complex 1j as a pale yellow solid was obtained. 1H NMR (300 MHz, CDCl3, T = 298 K, ppm) delta: 2.11-2.61 (m, 4H, CH2P), 3.40 (s, 3H, OCH3), 4.33-4.42 (m, 2H, CH=CH), 7.32-7.53 (m, 16H, PPh), 7.79-7.85 (m, 4H, PPh). 13C{1H} NMR (CDCl3, T = 298 K, ppm selected peaks) delta: 26.7 (m CH2, CH2P), 50.5 (CH3, OCH3), 52.9 (m, CH, CH=CH), 173.7 (C, CO). 31P{1H} NMR (CD2Cl2, T = 298 K, ppm) delta: 39.0. IR (KBr, pellet, cm-1): 1683 (nCO). Anal. Calcd. for C32H32O4P2Pd: C 59.22, H 4.97. Found: C 59.11, H 5.03., 52522-40-4

Reference£º
Article; Canovese, Luciano; Scattolin, Thomas; Visentin, Fabiano; Santo, Claudio; Journal of Organometallic Chemistry; vol. 834; (2017); p. 10 – 21;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

New downstream synthetic route of 14221-01-3

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,Tetrakis(triphenylphosphine)palladium,14221-01-3,its application will become more common.

A common heterocyclic compound, 14221-01-3,Tetrakis(triphenylphosphine)palladium, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14221-01-3

Into a 20 mL brown Schlenk tube were placed Pd(PPh3)4(0.05 mmol, 0.0578 g), PdCl2(MeCN)2 (0.05 mmol, 0.0130 g), norbornene(2.1 mmol, 0.2 g), and K2CO3 (2.0 mmol, 0.277 g). Then, 4-iodotoluene (2.0 mmol, 0.26 mL) as well as 8 mL DMA (containing 0.5 M H2O) were transferred to the tube by syringe under N2. The mixturewas stirred at 70 C for 20 h. The solutionwas washed withH2O and ether. The organic layer was extracted twice with ether. It was then purified by Centrifugal Thin Layer Chromatography (CTLC)using CH2Cl2 as eluent. The solvent was removed under reduced pressure. The yield of 5a is 98% (0.0848 g, 0.0980 mmol). The residue was subjected to crystallization process by CH2Cl2 and hexanesand yellow crystals were resulted. Similar processes were taken forthe preparation of 5b except that dicyclopentadiene (2.0 mmol,0.264 g) was used. The yield of 5b is 98% (0.0922 g, 0.0980 mmol). Yellow crystals were resulted in crystallization process by CH2Cl2and heptane.

Reference£º
Article; Chen, Ya-Qian; Hong, Fung-E.; Tetrahedron; vol. 71; 38; (2015); p. 7016 – 7025;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method