Catalyst palladium

The origin of a common compound about 14871-92-2

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),its application will become more common.

A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14871-92-2

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some scientific research about 14871-92-2

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,(2,2¡ä-Bipyridine)dichloropalladium(II),14871-92-2,its application will become more common.

A suspension of 1 mmol (0.333 g) of [Pd(bpy)Cl2] in 150 mL ofacetone was treated with 1 mmol (0.228 g) of benzyl dithiocarbamatesodium salt and the mixture was refluxed under continuousmagnetic stirring for 2 h. Stirring continued for another 12 h at 318 K and then filtered.The resulting yellow colored filtrate containing the desired productwas concentrated to 15 mL at 318 K. The orange precipitate formedwas filtered off and washed with diethyl ether. Recrystallizationwas done by dissolving the precipitate in minimum amount ofethanol. Yield: 0.336 g (70%) and decomposes at 207-209 C. Anal.Calcd. for C18H16N3S2ClPd (480.34 g mol-1) Found, (Calcd.) (%): C45.01, (45.05); H, 3.36 (3.34); N, 8.75 (8.76). Molar conductance forthe complex (10-3 M, H2O) is 9.0 mS m2 mol-1. FT-IR (KBr, cm-1):3405 upsilon(N-H); 3020 upsilon(Caro-H); 1550 upsilon(C-N); 1313 upsilons (CNS); 1036 upsilonas(CNS); 503 upsilon (Pd-N); 450 upsilon (Pd-S). 1H NMR (DMSO-d6-D2O, delta ppm):4.71 (d, 2H, H-c), 7.40 (m,1H, H-a), 7.32 (m, 4H, H-b), 8.54 (m, 2H, H-6,60), 8.27 (m, 2H, H-3,30), 8.18 (m, 2H, H-4,40), 7.68 (M, 2H, H-5,50)(Fig. 1). 13C NMR (DMSO-d6, delta ppm): 48.00 (C-e), 139.67 (C-5,5′),139.84 (C-4,4′), 140.00 (C-a), 140.17 (C-b), 140.34 (C-c), 140.50 (C-3,30), 140.60 (C-d), 140.67 (C-1,10), 140.76 (C-f) (Fig. 1). The NMRnumbering schemes are given in Fig. 1. UV-Vis data (H2O, lambdamax/nm,(log epsilon)): 312 (3.40), 249 (3.75), 187 (3.94).

Reference£º
Article; Saeidifar, Maryam; Mirzaei, Hamidreza; Ahmadi Nasab, Navid; Mansouri-Torshizi, Hassan; Journal of Molecular Structure; vol. 1148; (2017); p. 339 – 346;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

A new synthetic route of Tris(dibenzylideneacetone)dipalladium-chloroform

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,52522-40-4,Tris(dibenzylideneacetone)dipalladium-chloroform,its application will become more common.

A common heterocyclic compound, 52522-40-4,Tris(dibenzylideneacetone)dipalladium-chloroform, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 52522-40-4

Stage 2: Stage 1 material (8.50 g) and 3,5-bis(4-tert-butylphenyl)phenyl-1-boronic acid pinacol ester (15.50 g) were dissolved in toluene (230 mL). The solution was purged with nitrogen for 1 h before 2-dicyclohexylphosphino-2′,6′-dimethoxybiphenyl (66 mg) and tris(dibenzylidene)dipalladium (75 mg) were added using 10 mL of nitrogen-purged toluene. A 20wtpercent solution of tetraethylammonium hydroxide in water (60 mL) was added in one portion and the mixture as stirred for 20 h with the heating bath set to 105 ¡ãC. T.L.C. analysis indicated all the stage material had been consumed and only one fluorescent spot was observed. The reaction mixture was cooled and filtered into a separating funnel. The layers were separated and the aqueous layer extracted with toluene. The organic extracts were washed with water, dried with magnesium sulphate, filtered and concentrated to yield the crude product as a yellow/orange solid. Pure compound was obtained by column chromatography eluting with a gradient of ethyl acetate in hexanes followed by precipitation from DCM/methanol. HPLC indicated a purity of 99.75percent and a yield of 80percent (11.32g). 1H NMR (referenced to CDCl3): 7.83 (3H, d), 7.76 (6H, s), 7.73 (3H, s) 7.63 (12H, d) 7.49 (12H, d), 7.21 (3H, dd), 6.88 (3H, d), 4.28 (9H, s), 2.25 (3H, m), 1.98 (3H, m), 1.4-1.5 (57H, m), 1.23 (3H, m), 0.74 (9H, t), 52522-40-4

Reference£º
Patent; Cambridge Display Technology Limited; Sumitomo Chemical Co., Ltd; Kamtekar, Kiran; Steudel, Annette; EP2738195; (2014); A1;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some scientific research about (2,2¡ä-Bipyridine)dichloropalladium(II)

14871-92-2 A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

Synthesis of [Pd{OC(O)CH2N(COPh)}(bipy)] 2 A mixture of [PdCl2(bipy)] (210 mg, 0.63 mmol) with hippuric acid (113 mg, 0.63 mmol) and silver(I) oxide (600 mg) in dichloromethane (30 mL) was refluxed for 3.5 h. Methanol (30 mL) was added, and the mixture filtered to give a clear yellow solution. The solid residue was extracted with an additional 40 mL of dichloromethane-methanol (1:1 v/v), and the filtrates combined. The solution was evaporated to dryness, redissolved in dichloromethane (40 mL) and the product precipitated by addition of petroleum spirits (40 mL). The solid was filtered, washed with petroleum spirits (10 mL) and dried under vacuum to give 2 as an orange solid (192 mg, 69%). Found: C 50.2; H 3.45; N 9.1. C18H15N3O3Pd requires C 50.5; H 3.5; N 9.8%. (0043) 1H NMR, delta 9.12-6.91 (m, bipy and Ph), 4.26 (s, CH2). ESI MS (added NaHCO2, capillary exit voltage 140 V): [M+Na]+ m/z 461.88 (100%), calculated for C19H15N3O3PdNa m/z 462.00.

Reference£º
Article; Sim, Sophie A.; Saunders, Graham C.; Lane, Joseph R.; Henderson, William; Inorganica Chimica Acta; vol. 450; (2016); p. 285 – 292;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

The origin of a common compound about 52522-40-4

52522-40-4, 0.1328 g (0.4057 mmol) of 8-diphenylphosphine-2-methylquinoline, 0.0674 g (0.4261 mmol) of naphthoquinone and 0.2003 g(0.1935 mmol) of [Pd2(DBA)3CHCl3] were dissolved under inert atmosphere (Ar) in 30 ml of anhydrous acetone in a 100 ml necked flask. The mixture was stirred for 60 min at RT, the resulting orange solution treated with activated charcoal, filtered on a celite filter and concentrated under vacuum. The title complexwas precipitated as a paleorange solid by slow addition of diethylether, filtered off on a gooch, and washed with diethylether and n-pentane. 0.2039g (yield 89percent) of complex 1’b was obtained. 1H-NMR (300 MHz, CDCl3, T = 298 K, ppm) delta: 3.12 (s, 3H, quinoline-CH3), 4.98-5.05 (m, 2H, CH=CH) 7.06e7.13 (m, 2H, aryl naphthoquinone), 7.29-7.71 (m, 13H, H3, PPh2, aryl naphthoquinone), 7.79 (ddd,1H, J = 8.1, 7.5,1.4 Hz, H6), 7.90 (d,1H, J = 8.1, H7), 8.05 (dd, 1H, J = 7.5, 1.6 Hz, H5), 8.19 (dd, 1H, J = 8.4, 1.4 Hz, H4). 13C{1H}-NMR (CDCl3, T = 298 K, ppm) delta: 30.3 (CH3, quinoline-CH3), 62.7 (CH, CH=CH trans-N), 66.3 (d, CH, JCP = 21 Hz, CH=CH transP), 123.9 (CH, C3), 125.1 (CH, C5), 131.1 (CH, C7), 137.8 (CH, C6), 138.4 (CH, C4), 165.7 (d, C, JCP = 22.1 Hz, C9),165.7 (C, C2),184.0 (d, C, JCP = 6.2 Hz, CO transP), 185.2 (C, CO transN). 31P{1H}-NMR (CD2Cl2, T = 298 K, ppm) delta: 23.4. IR (KBr, pellet, cm-1): 1641 (nCO). Anal. Calcd. for C32H24NO2PPd: C 64.93, H 4.09, N 2.37. Found: C 65.06, H 3.98, N 2.21.

Reference£º
Article; Canovese, Luciano; Scattolin, Thomas; Visentin, Fabiano; Santo, Claudio; Journal of Organometallic Chemistry; vol. 834; (2017); p. 10 – 21;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

A new synthetic route of Tetrakis(triphenylphosphine)palladium

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14221-01-3,Tetrakis(triphenylphosphine)palladium,its application will become more common.

A common heterocyclic compound, 14221-01-3,Tetrakis(triphenylphosphine)palladium, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14221-01-3

General procedure: Into a 20 mL brown Schlenk tube were placed Pd(PPh3)4(0.05 mmol, 0.0578 g), PdCl2(MeCN)2 (0.05 mmol, 0.0130 g), norbornene(2.1 mmol, 0.2 g), and K2CO3 (2.0 mmol, 0.277 g). Then, 4-iodotoluene (2.0 mmol, 0.26 mL) as well as 8 mL DMA (containing 0.5 M H2O) were transferred to the tube by syringe under N2. The mixturewas stirred at 70 C for 20 h. The solutionwas washed withH2O and ether. The organic layer was extracted twice with ether. It was then purified by Centrifugal Thin Layer Chromatography (CTLC)using CH2Cl2 as eluent. The solvent was removed under reduced pressure. The yield of 5a is 98% (0.0848 g, 0.0980 mmol). The residue was subjected to crystallization process by CH2Cl2 and hexanesand yellow crystals were resulted. Similar processes were taken forthe preparation of 5b except that dicyclopentadiene (2.0 mmol,0.264 g) was used. The yield of 5b is 98% (0.0922 g, 0.0980 mmol). Yellow crystals were resulted in crystallization process by CH2Cl2and heptane., 14221-01-3

Reference£º
Article; Chen, Ya-Qian; Hong, Fung-E.; Tetrahedron; vol. 71; 38; (2015); p. 7016 – 7025;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

The origin of a common compound about 14871-92-2

General procedure: Silver tetrafluoroborate (AgBF4) (0.6 mmol) was dissolvedin methanol (7 mL); (2,2?-bipyridine) dichloropalladium(II)(Pd(Bpy)Cl2) (0.3 mmol) was dissolved in DMSO (1 mL),and then, the solutions were stirred together at ambient temperature0.5 h. Following gravity filtration, solid 3-hydroxyflavonederivative (0.3 mmol) and triethylamine (0.7 mL)were added to the filtrate. The reaction mixture was stirredfor 0.5 h (2 h for the Fla-OMe). The corresponding bipyridinepalladium flavonolato salt was then recovered usingvacuum filtration and recrystallized in CH3OH/CH3CN solvent;remaining solvent was removed in a vacuum desiccator overnight., 14871-92-2

Reference£º
Article; Han, Xiaozhen; Whitfield, Sarah; Cotten, Jacob; Transition Metal Chemistry; (2019);,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some scientific research about Tris(dibenzylideneacetone)dipalladium-chloroform

52522-40-4 A common heterocyclic compound, 52522-40-4,Tris(dibenzylideneacetone)dipalladium-chloroform, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

52522-40-4, tetrakis(triphenylphosphine)palladium(0) [generated in situ from tris(diphenylmethylideneacetone)dipalladium chloroform adduct (16 mg, 0.016 mmol) and triphenylphosphine 312 mg, 0.12 mmol)] ; tetrakis(triphenylphosphine)palladium (0) [generated in situ from tris(dibenzylideneacetone)dipalladium chloroform adduct (27 mg, 0.025 mmol) and triphenylphosphine (52 mg, 0.20 mmol)]

Reference£º
Patent; Universitetet i Olso; US2007/203159; (2007); A1;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

New downstream synthetic route of 14871-92-2

To a yellow suspension containing 0.30 g (0.90 mmol) of [Pd(bpy)Cl2] in water (20 mL) wereadded a solution containing 0.06 g (0.46 mmol) of HaptHCl in water (10 mL) and an aqueoussolution of NaOH (0.3 M, 10 mL). When the mixture was stirred at 50 C for 3 h, the suspensionturned to a yellow solution. After filtration, a saturated aqueous solution of NaNO3 (10 mL) wasadded to the yellow filtrate, followed by storing in a refrigerator for 1 week. The resulting yellowcrystals of [3](NO3)2 suitable for X-ray analysis were collected by filtration. Yield: 0.19 g (55%).

Reference£º
Article; Kouno, Masahiro; Miyashita, Yoshitaro; Yoshinari, Nobuto; Konno, Takumi; Chemistry Letters; vol. 44; 11; (2015); p. 1512 – 1514;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

A new synthetic route of 14871-92-2

General procedure: To a vigorously stirred solution of BzpheH2 (32.32 mg, 0.12 mmol) in 8 mL CH3OH/H2O (V:V 1:1), [Pd(bipy)Cl2] (20 mg, 0.06 mmol) was added. The mixture was heated to 50C and adjusted to pH 8-9 by NaOH solution, and then stirred for 2 h. The solution was concentrated to about 80% of the original volume. The complex I-a was separated from the solution after a few days.

Reference£º
Article; Wang, Li-Wei; Liu, Si-Yuan; Wang, Jin-Jie; Peng, Wen; Li, Sheng-Hui; Zhou, Guo-Qiang; Qin, Xin-Ying; Wang, Shu-Xiang; Zhang, Jin-Chao; Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry; vol. 45; 7; (2015); p. 1049 – 1056;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method