Category: 14871-92-2

A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14871-92-2

General procedure: Solid [Pd(L)Cl2] (L = bpy, phen) (0.2 mmol) was added to methanolic solution H2mesc (0.039 g, 0.2 mmol) containing KOH (0.0224 g, 0.4 mmol;; 15 mL). The mixture was stirred for 24 h. The yellow precipitate was filtered off, washed with methanol and air-dried. For [Pd(bpy)(mesc)]: Anal. Calc. For C20H15N2O4.5Pd: C, 52.0; H, 3.3; N, 6.1; Pd, 23.1%, Found: C, 52.1, H, 3.2; N, 6.0; Pd, 23.0%. Conductivity data (10-3 M in DMSO): LambdaM = 2.0 Ohm-1 cm2 mol-1. IR (cm-1); nu(C=O) 1664; nu(C-C) 1486; nu(C-O) 1254; nu(Pd-O) 521; nu(Pd-N) 427. 1H NMR (d6-DMSO/TMS, ppm), delta: CH3, 3.36; H(3), 6.66; H(8), 5.90; H(5), 6.50. ESI-MS: m/z: 905 (Calcd 904.8) [Pd(bpy)(mesc)]2+, 453 (Calcd 452.4) [Pd(bpy)(mesc)]+.

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),its application will become more common.

Reference£º
Article; Butler, Ian S.; Gilson, Denis F.R.; Jean-Claude, Bertrand J.; Mostafa, Sahar I.; Inorganica Chimica Acta; vol. 423; PB; (2014); p. 132 – 143;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), it is a common compound, a new synthetic route is introduced below.14871-92-2

To a vigorously stirred solution of BzpheH2 (32.32 mg,0.12 mmol) in 8 mL CH3OH/H2O (V:V D 1:1), [Pd(bipy)Cl2] (20 mg, 0.06 mmol) was added. The mixture was heatedto 50C and adjusted to pH D 8-9 by NaOH solution, andthen stirred for 2 h. The solution was concentrated to about80% of the original volume. The complex I-a was separatedfrom the solution after a few days. Yellow crystalline, yield: 68%. IR (KBr, cm1): n(Amide&)1551, n(OCO)a 1632, n(OCO)a1383, n(Pd-N) 566, n(Pd-O) 465. 1H NMR (600 MHz, d6-DMSO) d (ppm): 3.08 (dd, J D 13.1, 4.5 Hz, 1H, CH2-H),3.29 (dd, J D 13.1, 4.5 Hz, 1H, CH2-H), 5.08-5.05 (m, 1H,CH), 6.65 (t, J D 7.5 Hz, 1H, Ar-H), 6.73 (t, J D 7.5 Hz, 2H,Ar-H), 7.09 (d, J D 3.0 Hz, 3H, Ar-H), 7.13 (d, J D 5.4 Hz,1H, Ar-H), 7.23 (d, J D 7.2 Hz, 2H, Ar-H), 7.28 (d, J D5.4 Hz, 1H, Ar-H), 7.78-7.75 (m, 1H, Ar-H), 8.02 (t, J D7.8 Hz, 1H, Ar-H), 8.26 (d, J D 7.8 Hz, 1H, Ar-H), 8.30 (t, JD 6.9 Hz, 4H, Ar-H), 8.42 (d, J D 7.8 Hz, 1H, Ar-H). ESIMS:568.03 [MCK]C. Anal. Calcd. for [Pd(bipy)(Bzphe-N,O)] (C26H21N3O3Pd, 529.06): C, 58.93; H, 3.99; N, 7.93.Found: C, 58.84; H, 4.04; N, 7.84.

In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles. 14871-92-2, other downstream synthetic routes, hurry up and to see.

Reference£º
Article; Wang, Li-Wei; Liu, Si-Yuan; Wang, Jin-Jie; Peng, Wen; Li, Sheng-Hui; Zhou, Guo-Qiang; Qin, Xin-Ying; Wang, Shu-Xiang; Zhang, Jin-Chao; Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry; vol. 45; 7; (2015); p. 1049 – 1056;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Researchers who often do experiments know that organic synthesis is a process of preparing more complex target molecules from simple raw materials through one or more chemical reactions. Generally, it requires fewer steps,and cheap raw materials.14871-92-2,A new synthetic method of this compound is introduced below.14871-92-2

Solid [Pd(bpy)Cl2] (0.085 g, 0.25 mmol) was added to Hdahmp(0.04 g, 0.25 mmol) in ethanol (10 mL). Et3N (0.02 cm3, 0.20 mmol)was then added and the reaction mixture was refluxed for 48 h. Abrown precipitate was obtained which was filtered off, washedwith methanol and air-dried. Yield: 81%. Anal. Calc. for C14H13ClN6-OPdS: C, 36.9; Cl, 7.8; H, 2.9; N, 18.5; S, 7.0; Pd, 23.4. Found: C,37.1; Cl, 7.8; H, 2.8; N, 18.6; S, 7.2; Pd, 23.3%. Conductivity data(103 M in DMF): KM = 88.0 ohm1 cm2 mol1., 14871-92-2

If you are interested in these compounds, you can also browse my other articles.Thank you for taking the time to read this article. I hope you enjoyed it, (2,2¡ä-Bipyridine)dichloropalladium(II).

Reference£º
Article; El-Morsy, Fatema A.; Jean-Claude, Bertrand J.; Butler, Ian S.; El-Sayed, Shadia A.; Mostafa, Sahar I.; Inorganica Chimica Acta; vol. 423; PB; (2014); p. 144 – 155;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

In the chemical reaction process,reaction time,type of solvent,can easily affect the result of the reaction, thereby determining the yield and properties of the reaction product.An updated downstream synthesis route of 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), as follows.14871-92-2

14871-92-2, General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

According to the analysis of related databases, 14871-92-2, the application of this compound in the production field has become more and more popular.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), it is a common compound, a new synthetic route is introduced below.

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles. 14871-92-2, other downstream synthetic routes, hurry up and to see.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2,Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. (2,2¡ä-Bipyridine)dichloropalladium(II),14871-92-2, This compound has unique chemical properties. The synthetic route is as follows.

(bpy)PdCl2 (167 mg, 0.5 mmol) and AgNO3 (170 mg, 1.0 mmol) was mixed in CH3NO2 (40 mL). The mixture was stirred at 60 C for 24 hrs, and the white AgCl precipitate was filtered by a short pad of celite. The filtrate was sampled for ESI-HRMS, and cationic C20H18N4O2Pd22+ (m/z: 279.9743) was observed. Then the filtrate was concentrated and recrystallized to give 25 mg light yellow needle-like solid. Yield 9.0%.

If you are interested in these compounds, you can also browse my other articles.Thank you for taking the time to read this article. I hope you enjoyed it, 14871-92-2.

Reference£º
Article; Yang, Zhenyu; Ni, Yuxin; Liu, Rui; Song, Kaixuan; Lin, Shaohui; Pan, Qinmin; Tetrahedron Letters; vol. 58; 21; (2017); p. 2034 – 2037;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

In the chemical reaction process,reaction time,type of solvent,can easily affect the result of the reaction, thereby determining the yield and properties of the reaction product.An updated downstream synthesis route of 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), as follows.14871-92-2

General procedure: Silver tetrafluoroborate (AgBF4) (0.6 mmol) was dissolvedin methanol (7 mL); (2,2?-bipyridine) dichloropalladium(II)(Pd(Bpy)Cl2) (0.3 mmol) was dissolved in DMSO (1 mL),and then, the solutions were stirred together at ambient temperature0.5 h. Following gravity filtration, solid 3-hydroxyflavonederivative (0.3 mmol) and triethylamine (0.7 mL)were added to the filtrate. The reaction mixture was stirredfor 0.5 h (2 h for the Fla-OMe). The corresponding bipyridinepalladium flavonolato salt was then recovered usingvacuum filtration and recrystallized in CH3OH/CH3CN solvent;remaining solvent was removed in a vacuum desiccator overnight., 14871-92-2

The basis of chemical reaction formula synthesis, the synthesis route is composed of some specific reactions and combined according to certain logical thinking. 14871-92-2, We look forward to the emergence of more reaction modes in the future.

Reference£º
Article; Han, Xiaozhen; Whitfield, Sarah; Cotten, Jacob; Transition Metal Chemistry; (2019);,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

In the chemical reaction process,reaction time,type of solvent,can easily affect the result of the reaction, thereby determining the yield and properties of the reaction product.An updated downstream synthesis route of 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), as follows.14871-92-2

[Pd(bpy)Cl2] (0.10 g, 0.30 mmol) was suspended in water (4 mL). Lactic acid (0.03 g, 0.28 mmol) and 1 M NaOH (0.60 mL) were dissolved in water (10 mL) and then added to the mixture, which was heated under reflux at 150 C with continuous stirring until a clear yellow solution was obtained. The solution was filtered and acetone (10 mL) was added to the solution. The reaction mixture was cooled to 4 C for a long time (2 months), resulting yellow crystals of complex 5. Yield: 33%. m.p.: 250 C. Elemental Anal. Calc. for C13H13ClN2OPd (355.10): C, 44.0; H, 3.7; N, 7.9. Found: C, 44.1; H, 3.6; N, 7.8%. IR (KBr, numax/cm-1): 1634 s, nu(CO); 1621 s, nu(CC); 1496 m, 1443 s, nu(CC,CN). Far-IR (Nujol, numax/cm-1): 333 m, nu(Pd-Cl); 285 m, nu(Pd-C); 243 m, nu(Pd-N). 1H NMR (CDCl3, delta/ppm): 2.40 (s, 3H, c), 3.01 (s, 2H, a), 7.61 (m, 2H, 5,5?), 8.02 (m, 4H, 3,3? and 4,4?), 9.31, 9.51 (2d, 2H, 6,6?).

The basis of chemical reaction formula synthesis, the synthesis route is composed of some specific reactions and combined according to certain logical thinking. 14871-92-2, We look forward to the emergence of more reaction modes in the future.

Reference£º
Article; Balboa, Susana; Carballo, Rosa; Castineiras, Alfonso; Gonzalez-Perez, Josefa Maria; Niclos-Gutierrez, Juan; Polyhedron; vol. 50; 1; (2013); p. 512 – 523;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), it is a common compound, a new synthetic route is introduced below.

General procedure: [Pd(bpy)Cl2] (0.20 g, 0.60 mmol) was suspended in water (25 mL). Silver nitrate (0.20 g, 1.19 mmol) in water (5 mL) was added and the reaction mixture was stirred for 6 h at 60 C and then at room temperature, always in absence of light. The resulting solution was centrifuged and filtered to remove AgCl. A few drops of water, glycolic acid (0.05 g, 0.66 mmol) and 1 M NaOH (1.20 mL) were added to the filtrate. The resulting solution was stirred for 5 days and concentrated at 60 C to 5 mL on a rotary evaporator. The mixture was cooled to room temperature and the yellow powder was filtered off and dissolved from water and again concentrated to 5 mL. Yellow single crystals suitable for X-ray diffraction were obtained from the resulting solution by slow evaporation at room temperature., 14871-92-2

In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles. 14871-92-2, other downstream synthetic routes, hurry up and to see.

Reference£º
Article; Balboa, Susana; Carballo, Rosa; Castineiras, Alfonso; Gonzalez-Perez, Josefa Maria; Niclos-Gutierrez, Juan; Polyhedron; vol. 50; 1; (2013); p. 512 – 523;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

As we all know, there are many different methods for the synthesis of a compound, and people can choose the synthesis method that suits their own laboratory according to the actual situation. 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), This compound is widely used in many fields, so it is necessary to find a new synthetic route. The downstream synthesis method of this compound is introduced below.14871-92-2

[Pd(bpy)Cl2] (.67 g, 2 mmol) was suspended in 200 mlacetone-water (3:1 v/v) and AgNO3 (.68 g, 4 mmol) wasadded with constant stirring. This mixture was heated at328 K with stirring in the dark for 6 h followed by stirringfor 16 h at room temperature. The AgCl precipitatewas removed by filtration using Whatman 42 filter paper.The clear yellow filtrate was mixed with mu-paraxylidinebisdithiocarbamatedisodium salt (.33 g, 1 mmol).The reaction mixture was subsequently stirred for 5 h at318 K and then filtered. The clear solution was concentratedto 5 ml at 318 K. The resulting yellow precipitatewas filtered and washed with small amounts of acetoneand resolved in 300 ml doubly distilled water at 318 K.The solution was filtered to remove turbidity. The clearsolution was then concentrated to 5 ml and refrigeratedovernight. The yellow precipitate was filtered and washedwith small amounts of cold distilled water and acetoneand dried in an oven at 318 K. The synthesis of the complexcan be summarized by Figure 1. Yield: .572 g(65%), Decomposition ranges: 520-523 K. Anal. Calcd.for C30H26N6S4Cl2Pd2: C, 40.86; H, 2.95, N, 9.53%.Found: C, 40.85; H, 2.96, N, 9.55%. Molar conductance,LambdaM (H2O, Omega-1 mol-1 cm2): 243. FT-IR (KBr pellets,cm-1): 1541 upsilon (C-N); 1022 upsilon (C-S) and 1385 (NO3- ion).UV-Vis data (water, lambdamax/nm (logepsilon): 308 (3.43), 247 (3.79) and 188 (3.95). 1H NMR (500 MHz, DMSO-d6,ppm, d = doublet, t = triplet and m = multiple): 7.66 (m,1H, H-a), 8.23 (m, 2H, H-b), 8.48 (d, 2H, H-c), 7.79(t, 2H, H-5,5), 8.30 (t, 2H, H-4,4), 8.57 (d, 2H, H-3,3),8.88 (d, 2H, H-6,6) (Figure S1).

If you are interested in these compounds, you can also browse my other articles.Thank you for taking the time to read this article. I hope you enjoyed it, (2,2¡ä-Bipyridine)dichloropalladium(II).

Reference£º
Letter; Saeidifar, Maryam; Sohrabi Jam, Zahra; Shahraki, Somayeh; Khanlarkhani, Ali; Javaheri, Masoumeh; Divsalar, Adeleh; Mansouri-Torshizi, Hassan; Akbar Saboury, Ali; Journal of Biomolecular Structure and Dynamics; vol. 35; 12; (2017); p. 2557 – 2564;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method